[jsntpx]

Trendsetter 3244
Error Messages
See also Search Form
This content is generated by scripts that pull information directly from Firmware Engineering's support site. The scripts were last run: 31 Jan 2005 05:00:02
Number Error Message
00000 MISC:
00001 MISC: Reserved
00002 MISC: Reserved
00003 MISC: Reserved
00004 MISC: Reserved
00005 MISC: Reserved
00006 MISC: Reserved
00007 MISC: Reserved
00020 MISC: Specified test is not defined
00021 MISC: Workstation communications lost
00030 MISC: Requested command is not defined
00100 MISC: MPE Code checksum is faulty
00101 MISC: LCA module checksum is faulty
00102 MISC: LCA module incompatable format
00103 MISC: Module not found in version list
00104 MISC: Firmware module checksum is faulty
00105 MISC: Error opening firmware module
00106 MISC: Invalid or unneeded code bundled with firmware
00107 MISC: Missing required code in the firmware bundle
00108 MISC: Product version not found in version list
00109 MISC: Invalid version of overwriting pattern
00200 MISC: Code bank selected for loadingis current code bank
00201 MISC: Flash memory program failed
00202 MISC: Address <hex address> out of memory bank range
00203 MISC: Unsupported memory type detected
00204 MISC: Flash memory erase failed
00500 MISC: Temperature log: Engine = <Celcius x 10> Leadscrew = <Celcius x 10>
00501 MISC: Password not set!
00502 MISC: NVS modified and saved, but not backed up!
00511 MISC: Dongle not responding
00512 MISC: Config: %s %s owner %s
01000 RESET: cause unknown
01001 RESET: induced by test submodule
01002 RESET: induced by RESET opcode, possible warm reset requested at monitor
01004 RESET: induced by loss of clock
01016 RESET: induced by halt monitor
01032 RESET: induced by software watchdog, possible cold reset requested at monitor
02000 NVS: checksum error in <NVS subsystem> calibration block
02040 NVS: checksum error in <NVS subsystem> configuration block
02080 NVS: checksum error in mode <number> table
02200 NVS: low battery in NVS detected
02201 NVS: NVS automatically upgraded to version 2
02202 NVS: subscan size nvs config parameter is invalid
03000 WSCOMM: All faults cleared
03001 WSCOMM: Invalid command letter
03002 WSCOMM: Parameter syntax error
03003 WSCOMM: Defined WS command is currently unsupported
03004 WSCOMM: Character pacing timeout, WS transmitting too slowly
03005 WSCOMM: too many characters in command string
03006 WSCOMM: Could not open serial communications interface for workstation
03007 WSCOMM: Resume or clear received when not suspended
03008 WSCOMM: Command received for idle image ID
03009 WSCOMM: Specified image ID is already active
03010 WSCOMM: Maximum active image commands surpassed
03011 WSCOMM: Resolution specified is not available
03012 WSCOMM: Already aborting
03014 WSCOMM: Abort received when no command active
03015 WSCOMM: Already imaging
03016 WSCOMM: Recorder is flushing, can't accept new commands
03017 WSCOMM: Door is open
03018 WSCOMM: Door is closed
03019 WSCOMM: ABORT switch on
03020 WSCOMM: ABORT switch off
03021 WSCOMM: Operation aborted at recorder - check that abort switch is released
03022 WSCOMM: Operation aborted by workstation
03023 WSCOMM: ABORT complete
03024 WSCOMM: Abort request not heeded within timeout, possible hung subsystem
03025 WSCOMM: Task(s) <task codes> did not finish initializing on time
03026 WSCOMM: Operation preempted
03027 WSCOMM: Cassette bay door open
03028 WSCOMM: Cassette bay door closed
03047 WSCOMM: Resolution does not exist
03048 WSCOMM: Image too wide for plate
03055 WSCOMM: Workstation software error - Invalid packet number
03056 WSCOMM: Workstation software error - Invalid total packets number
03057 WSCOMM: Workstation software error - Out of sequence packet received
03058 WSCOMM: Workstation software error - Invalid packet length
03059 WSCOMM: Workstation software error - Invalid Media Imaging Mode ID (MIMID)
03060 WSCOMM: Packet fails CRC check
03061 WSCOMM: Total packet data exceeding firmware buffer capacity
04001 MSG: Command parameter error
04002 MSG: Parameter is out of range
04003 MSG: Defined command is currently unsupported
04004 MSG: Requested test pattern not defined
04005 MSG: <subsystem> is already reserved
04006 MSG: Reserved message in message pool
04007 MSG: Task releasing message owned by another task
04008 MSG: Task releasing unreserved message
04009 MSG: Task sending message owned by another task
04010 MSG: Task sending unreserved message
04011 MSG: Task received message that was not sent
04012 MSG: Reserved string in string pool
04013 MSG: Task releasing unreserved string
04014 MSG: Task releasing string owned by another task
04015 MSG: Task reserving released string
04016 MSG: <task name> timed out while waiting for command <hex command code>
04017 MSG: <task name> received an invalid command (command = <hex command code>)
04018 MSG: Wrong number of parameters
04019 MSG: Inactive list sent
04020 MSG: Unexpected list type sent
04021 MSG: Invalid list entry number sent - Possible version incompatabilities
04022 MSG: Plot mode not specified before plot parameters
04024 MSG: Task received msg with unexpected id (code = %X)
04028 MSG: suspended - waiting for Resume or Clear
04029 MSG: plate thickness too large
04030 MSG: one or both plate dimensions too large
04031 MSG: media type out of range
04032 MSG: one or both plate dimensions too small
04034 MSG: media %d not supported
06000 DRUM: Timeout on drum operation
06001 DRUM: Illegal command state machine state
06002 DRUM: Timeout waiting for drum move
06003 DRUM: Received invalid command
06004 DRUM: drum not initialized - can't execute that command
06005 DRUM: Unexpected status returned from function
06006 DRUM: Timeout during active braking
06007 DRUM: Timeout on velocity settling
06008 DRUM: Timeout on velocity acceleration
06009 DRUM: Sample interrupt failure
06011 DRUM: Servo amp fault
06012 DRUM: Cable from motherboard to drum servo amp not detected
06013 DRUM: Index not detected
06014 DRUM: Extra Tach A pulse detected
06015 DRUM: Missing Tach A pulse
06016 DRUM: Extra Tach B pulse detected
06017 DRUM: Missing Tach B pulse
06018 DRUM: Drive direction incorrect - check motor wiring
06019 DRUM: Tach encoder cable not detected
06020 DRUM: Aborted
06021 DRUM: Timeout on hold
06022 DRUM: Motor current exceeded limit
06023 DRUM: Velocity error - drum rotation blocked or PID gain settings wrong
06024 DRUM: Position error is greater than 1000 ticks
06025 DRUM: Hall velocity error - drum rotation blocked or PID gain settings wrong
06026 DRUM: Timeout waiting for TPU hall sensor PW measurement
06027 DRUM: Plate not loaded correctly on drum, obstruction detected below LEC actuator
06028 DRUM: ALE actuators on drum
06029 DRUM: Hall mode overspeed error - possible TPU failure
06030 DRUM: Drum hall velocity does not match encoder velocity to within tolerance.
06031 DRUM: Drum is spinning.
06033 DRUM: Index detected prematurely - clean encoder disc or re-align encoder
06034 DRUM: Drum won't settle with zero torque applied - requires drum cal
06036 DRUM: Drum Position error during Velocity mode, (check acceleration setting)
06037 DRUM: Drum velocity greater than xx rpm in Position mode, possible runaway
06038 DRUM: LCA tick counter annomaly, premature index or spurious counter reset
06039 DRUM: Drum Position error during Velocity mode, (extra index possible cause, check monitor values)
06040 DRUM: Encoder counted extra ticks
06041 DRUM: Index occurred at xx, more than 3 ticks before normal ticks per rotation
06042 DRUM: Hall velocity error - more than 20 percent during drum init.
07000 CARRIAGE: Limit switches reporting carriage is both HOME and AWAY
07001 CARRIAGE: stuck in HOME position
07002 CARRIAGE: stuck in AWAY position
07003 CARRIAGE: unexpectedly arrived at HOME position
07004 CARRIAGE: unexpectedly arrived at AWAY position - image size may have been too large
07005 CARRIAGE: operation timed out
07006 CARRIAGE: timed out while waiting for LCA position
07007 CARRIAGE: position register not accurate
07008 CARRIAGE: LCA's not configured at startup
07009 CARRIAGE: ALE not taken out of reset
07010 CARRIAGE: Unexpected error: 0x%x
07011 CARRIAGE: could not find edge of platecheck that plate size is entered correctly
07012 CARRIAGE: did not reach target speed
07013 CARRIAGE: step synth position register reserved
07015 CARRIAGE: Head Stage is at it's away position, unsafe to move carriage
07016 CARRIAGE: ALE board timed out during carriage position read
07017 CARRIAGE: Carriage state error. Current state: <description>, jog_count = <n> JOG = <number> PLOT = <number>
07018 CARRIAGE: Carriage illegal dest. Current %lu, Dest %lu Stop Dist %lu
07019 CARRIAGE: Specified Speed exceeds maximum of %lu
07020 CARRIAGE: Carriage control board error: cable not detected or undervoltage
07021 CARRIAGE: Carriage control board error: over current
07022 CARRIAGE: Carriage control board error: over temperature
08000 PROC: Processor not present or turned off
08001 PROC: Processor is not ready
08002 PROC: Processor fault requires immediate attn.
08003 PROC: Processor warning will need attention
08004 PROC: Processor type unknown
08005 PROC: Illegal processor number used
10012 HARDWARE: Carriage limit switch
10019 HARDWARE: ALE is not plugged in
10020 HARDWARE: DPE is not plugged in
10022 HARDWARE: MPE LCA's not configured at startup
10023 HARDWARE: DPE will not initialize, may be stuck in reset
10025 HARDWARE: DPE LCA's not configured at startup
10026 HARDWARE: Incorrect DPE version installed
10050 HARDWARE: RAM DAC Incrementing Address Test fail - Address = <fault address>, Write data = <hex data>, Readdata = <hex data>
10051 HARDWARE: DPE failure - dpath control write = <hex data>, read = <hex data>
10060 HARDWARE: External Debris Blower Filters Not Present
10061 HARDWARE: External Debris Blower Filters Full
10062 HARDWARE: External Debris Blower Filters Almost Full (Vacuum Level %d is below %d)
10063 HARDWARE: External Debris Blower System Blocked (Vacuum Level %d is above %d)
10064 HARDWARE: External Debris Blower Not Connected or Filters Full (Vacuum Level %d is below %d)
10065 HARDWARE: DBlower Filter Fault.
11000 CABLE: HA-BP cbl, Carriage Home/Away
11002 CABLE: EH-BP: Exposure Head - Backplane
11003 CABLE: TE-BP: Tach Encoder - Backplane
11004 CABLE: MD-BP: Drum Motor - Backplane
11005 CABLE: Chiller/Blower sensor cbl.
11504 CABLE: SPR-BP
11575 CABLE: Operator Interface not connected
11576 CABLE: Pushbutton not connected
11582 CABLE: CD-D-BP: Carriage Drive Digital
11583 CABLE: CD-A-BP: Carriage Drive Analog
11584 CABLE: CM-CDB: Carriage Drive to Motor
11593 CABLE: Sensors not connected (J7)
11594 CABLE: Air Valves not connected (J20)
11595 CABLE: LR plate sensor not connected (J3)
11596 CABLE: Fly-off cable not connected (J2)
11597 CABLE: Temp Sensors not connected (J13)
12000 POWER: ALE +12V
12001 POWER: ALE -12V
12002 POWER: Carriage power
12006 POWER: Carriage Amp Fault
12007 POWER: Exposure Head power
12008 POWER: Drum Amp Fault
12701 POWER: TEE +24V
13000 EHBOOT: internal message timeout
13001 EHBOOT: datalink terminated the program sequence prematurely
13002 EHBOOT: format error detected during data transfer
13003 EHBOOT: sumcheck error detected during data transfer
13004 EHBOOT: datalink programming sequence taking too long
13005 EHBOOT: LOADER echo mismatch during bootstrap sequence
13006 EHBOOT: LOADER not echoed during bootstrap sequence
13007 EHBOOT: no break detected after forcing head into bootstrap mode
13008 EHBOOT: cannot perform requested operation, no LOADER present
13009 EHBOOT: LOADER prompt for next primitive did not arrive
13010 EHBOOT: communications error
13011 EHBOOT: failed to program location <hex data> with data <hex data>
13012 EHBOOT: failed to erase device, stopped at location <hex data>
13013 EHBOOT: failed to respond to programming command
13014 EHBOOT: Timeout on byte <byte #> while waiting for exposure head to complete response string
13015 EHBOOT: ENQ expected and not received
13016 EHBOOT: ACK expected and not received
13017 EHBOOT: incorrect response length
13018 EHBOOT: incorrect version length
13019 EHBOOT: incorrect version response in byte <byte #>
13020 EHBOOT: incorrect response address
13021 EHBOOT: incorrect response data
14000 SAT: Satellite error cleared
14002 SAT: Unknown Satellite Output Register: <hex number>
14003 SAT: Satellite SW corrupted Buffer
14004 SAT: Buffer Restore error during Output Command
14050 SAT: QSPI error during configuration
14051 SAT: Timeout during SPI enable
14052 SAT: Timeout during QSPI disable
14053 SAT: Timeout during SPI execution
14054 SAT: SPI Mode Fault error
14055 SAT: QSPI Update Watchdog timeout
14056 SAT: <Satellite Board> Error: <Output Name>
14057 SAT: Error Detection Error: Address <address>, Bit = <bit number>
14100 SAT: Temperature Filter Error: Out of range
14101 SAT: LUE Analog testpoint exceeded allowed maximum
14102 SAT: LUE Analog testpoint exceeded allowed minimum
14103 SAT: Engine Frame temperature out of range
14104 SAT: Engine Leadscrew temperature out of range
14105 SAT: Spare sensor 0 temperature out of range
14106 SAT: Spare sensor 1 temperature out of range
14107 SAT: Timeout waiting for conveyor roller speed to update
14108 SAT: Timeout waiting for conveyor belt speed to update
14150 SAT: Cassette Bay <bay number> invalid, autoloader currently configured for <max> bays
14151 SAT: Cassette Bay <bay number> Error: <device>
14200 SAT: PPE Analog testpoint exceeded allowed maximum
14201 SAT: PPE Analog testpoint exceeded allowed minimum
14202 SAT: Software error: invalid lamp state %d in sat_set_lamp_state()
14203 SAT: Software error: invalid image task state %d in sat_update_lamps()
15059 ALE: Autoloader is not initialized, possibly due to an opened door
15062 ALE: plate loaded incorrectly, remove plate from drum
15068 ALE: move clamps to park position, then select RESUME
15071 ALE: remove plate from drum
15072 ALE: remove plate partially on drum
15073 ALE: trailing edge clamp status conflict, setting te state flag to<0|1>. ( "1" indicates "on drum", "0" indicates "on tec backbone" )
15074 ALE: trailing edge clamps failed to unlock
15075 ALE: trailing edge clamps failed to lock
15076 ALE: trailing edge clamps not on actuator
15077 ALE: trailing edge clamps already on actuator, possible sensor or software error.
15078 ALE: no plate on drum
15079 ALE: timeout moving leading edge cylinder
15080 ALE: timeout moving trailing edge cylinder
15082 ALE: timeout moving roller cylinder
15085 ALE: roller on drum
15086 ALE: leading-edge actuator on drum
15087 ALE: trailing-edge actuator on drum
15250 ALE: timeout waiting for load button to be pressed
15251 ALE: plate not detected on load ramp
15252 ALE: plate larger than expected
15253 ALE: plate smaller than expected
15254 ALE: remove plate detected on load ramp
15259 ALE: load ramp is tilted into drum no-fly zone
15281 ALE: Please load plate
15283 ALE: Please unload plate
16005 IMAGE: update received after load started
16006 IMAGE: task received incorrect ID
16007 IMAGE: Inactive image task received image update
16008 IMAGE: Total mainscan shift less than or equal to zero
16009 IMAGE: Total subscan shift less than zero
16010 IMAGE: Total mainscan shift too large
16011 IMAGE: PLL is not able to track drum motion
16012 IMAGE: PLL was not able to maintain drum motion tracking
16013 IMAGE: Specified \"around drum\" image size too large
16018 IMAGE: exposure too low
16021 IMAGE: mainscan length must be a multiple of 16
16022 IMAGE: command received when already suspended
16023 IMAGE: plate exposed by open door
16025 IMAGE: Stroke must be flat when calibrating scorr
16026 IMAGE: Scorr must be initialized in current mode before calibrating
16027 IMAGE: TPG not idle after imaging, DPE reset
16028 IMAGE: Series plot completed
16030 IMAGE: Series strip width is set to zero
16038 IMAGE: Total number of retraces: <retraces>
16050 IMAGE: DPE orthog slope less than 0, check plate rotation
16051 IMAGE: DPE orthog slope larger than max, check plate rotation
16054 IMAGE: Attempt to image B-side before A-side
16056 IMAGE: Plate imaging has begun
16068 IMAGE: Unable to initialize plot for mode set to 0 DPI
16073 IMAGE: Negative media (inverted data) requires FDPE
17000 HEAD: No mailbox defined for datalink task
17001 HEAD: Error while sending to datalink mailbox
17002 HEAD: Datalink synchronization lost
17003 HEAD: Datalink failed while retrying send
17004 HEAD: Datalink in programming mode, command not valid
17005 HEAD: Datalink already in programming mode
17006 HEAD: Datalink timed out waiting for break
17007 HEAD: fault code = <hex data>, status byte = <hex data>
17008 HEAD: command timed out
17009 HEAD: task received unexpected head message <mailbox>, message code <msgtype>h
17010 HEAD: command acknowledge fault = <hex number>
17013 HEAD: couldn't find plate edge due to dirty edge strip on drum
17014 HEAD: won't come online
17015 HEAD: did not signal end of initialization
17016 HEAD: is not responding
17021 HEAD: break detected, exposure head has reset
17046 HEAD: multiple edges detected - verify image position
17501 HEAD: temperature out of range
17502 HEAD: value out of range
17503 HEAD: missing laser on parameters
17504 HEAD: attempted write blocked
17505 HEAD: failure to write to memory
17506 HEAD: unsupported message
17507 HEAD: message length incorrect
17508 HEAD: invalid control message
17509 HEAD: operation was aborted
17532 HEAD: no more room in mailbox
17533 HEAD: ran out of buffers
17534 HEAD: all retries failed on chnl 0
17535 HEAD: all retries failed on chnl 1
17536 HEAD: sync lost on chnl 0
17537 HEAD: sync lost on chnl 1
17548 HEAD: CONFIG register incorrect
17549 HEAD: flash memory checksum error
17550 HEAD: LCA won't init for reprogram
17551 HEAD: LCA won't admit being loaded
17552 HEAD: SRAM memory check failure
17596 HEAD: software error
17597 HEAD: LCA config unavailable
17692 HEAD: Light level too low for Beam Pointing
17693 HEAD: Timeout waiting for LASER OK
17694 HEAD: Light valve high voltage fault
17695 HEAD: LV Positive 12V fault (bipolar)
18017 LASER: Cannot continue, laser is not ready
19000 PDB: Air Supply Below Threshold
21000 SCSI: SCSI bus reset while imaging
21001 SCSI: SCSI parity error while imaging, check plate for artifacts
21002 SCSI: SCSI driver error, invalid initiator
21003 SCSI: SCSI Driver Error, line <line number>
21004 SCSI: SCSI asynchronous transfer requested, line <line number>
21005 SCSI: timed out waiting for SCSI complete
30000 TPG: memory overflow
30001 TPG: too many scans
30002 TPG: write to closed scan
30003 TPG: write to unopened scan
30004 TPG: write to undefined scan
30005 TPG: close of closed scan
30006 TPG: close of unopen scan
30007 TPG: open of NULL scan
30008 TPG: Undefined pattern number, use "list pattern"
30009 TPG: Call with NULL pattern struct
30010 TPG: Pattern write call error
30011 TPG: Too many cells in pattern
30012 TPG: timed out waiting for stripe to complete
31002 LCA: DONE signal stuck low while programming
31003 LCA: READY signal stuck low while programming
31004 LCA: did not accept programming data
31006 LCA: INIT signal stuck low while programming
31007 LCA: INIT signal stuck high while programming
31008 LCA: Required LCA file is not in firmware
31009 LCA: Required LCA master file is not in firmware
31010 LCA: Length of LCA diff file does not match master
32200 SW: Ink Key buffers out of synch
32201 SW: Image shutdown error
32202 SW: NCO update timeout
32203 SW: Resolution mode not defined
32301 SW: Unknown ID code in firmware directory
32302 SW: undefined subsystem in NVS list
32401 SW: Could not open console interface for serial communications
32403 SW: Could not open head interface for serial communications
32404 SW: Could not open laser interface for serial communications
32450 SW: Out of memory
32480 SW: WS data list unexpectedly in use
32481 SW: WS command pattern incorrect
32490 SW: AL Sched: pick sync error
32491 SW: AL Sched: unload sync error
32492 SW: AL Sched: load sync error
32493 SW: AL Sched: process sync error
32500 SW: Unexpected SW failure - general exception
32600 SW: executive call failed
32601 SW: executive call tsk_create() failed
32602 SW: executive call tsk_delete() failed
32603 SW: executive call tsk_suspend() failed
32604 SW: executive call tsk_resume() failed
32605 SW: executive call tsk_set_priority() failed
32606 SW: executive call mbx_create() failed
32607 SW: executive call mbx_delete() failed
32608 SW: executive call mbx_send() failed
32609 SW: executive call mbx_receive() failed
32610 SW: executive call mbx_flush() failed
32611 SW: executive call buf_alloc() failed
32612 SW: executive call buf_free() failed
32613 SW: executive call tmr_create() failed
32614 SW: executive call tmr_delete() failed
32615 SW: executive call pip_create() failed
32616 SW: executive call pip_delete() failed
32617 SW: mbx_send failed, NULL mailbox
32618 SW: mbx_send failed, mailbox full
32700 SW: all tasks suspended
32701 SW: Unexpected message in mailbox <mailbox name>, message code <hex message code>
32702 SW: message buffer request failed
32703 SW: message buffer release failed
32704 SW: string buffer request failed
32705 SW: string buffer release failed
32706 SW: unexpected case - file:<filename> line:<line number>
32707 SW: image command received by active task
32708 SW: procedure call has invalid parameters
32709 SW: status mask has duplicate flags defined
32710 SW: Invalid status code for this command code: <hex command code>
32711 SW: Unexpected message type for this command. type: <hex message type>
32766 SW: Non-specific error

[Smhily]

可否有中文解说。或是上传。非常谢谢。英文的毕竟还是看不懂。。。。

[zamdy]

怪不得啊怪不得，原来在这里，全胜1代？

[xcj_xu]

好东西，不过是中文的就更好了。

[tianyubox]

很好的资料，英文水平有限要慢慢翻释