施乐C800 出现45-381代码不知道是哪里有问题啊电话给工程师又遇上周末救命啊

poet33 · 2013-06-15, 23:23

施乐C800 出现45-381代码不知道是哪里有问题啊电话给工程师又遇上周末救命啊

AQBJ12 · 2013-06-16, 00:52

045-381 PH_1 MD PWB Fuse Fail
Detection Condition
The Fuse on the PH_1 MD PWB has blown.

Warning
Before doing any procedure other than such checks as diagnostic ones that are made with the machine alive, be sure to turn OFF the machine.

Electrical Parts to Check
The table shows the electrical parts related to this Fault Code for display. Utilize information on the table below for making a decision as to whether an electric part is good or not. After making a decision, replace the part as required.

When checking electrical parts, check connectors as well.

To decide whether individual parts such as sensors and motors are defective, go to 2.2.4 Generic FIPs.

Table 1 No.
Related Electrical Part
Location
Condition Check
Ref. BSD/WN
PL

1
PH_1 MD PWB
7.4.2-18
Refer to 2.2.1
CH1.40, CH1.27, CH1.28, CH1.29, CH1.30 / 7.2.1.64, 7.2.1.66, 7.2.1.69, 7.2.1.72
PL 18.2

2
DST 1 (IOT-L) PWB
7.4.1-6
Refer to 2.2.1
CH1.27, CH1.28, CH1.29, CH1.30, CH1.12, CH1.13, CH1.14, CH1.15 / 7.2.1.64, 7.2.1.66, 7.2.1.69, 7.2.1.72, 7.2.1.55, 7.2.1.56
PL 18.11

3
FLY 1 PWB
7.4.1-16
-
CH1.12 / 7.2.1.55
PL 18.11

4
LVPS S24-1
7.4.17-37
REP 18.12.2
CH1.12 / 7.2.1.55
PL 18.12

5
FLY 3 PWB
7.4.1-15
-
CH1.13 / 7.2.1.55
PL 18.11

6
LVPS S24-2
7.4.17-38
REP 18.12.2
CH1.13 / 7.2.1.55
PL 18.12

7
LVPS S24-3
7.4.17-16
REP 18.12.2
CH1.14 / 7.2.1.56
PL 18.12

8
FLY 6 PWB
7.4.1-11
-
CH1.15 / 7.2.1.55
PL 18.11

**修施乐的海贼** · 2013-06-16, 09:55

奇怪了为何我和楼上这位查到的信息居然是有些出入的
不过大致差不多的
难道800的手册还有狠多版本吗

045-.jpg

045-1.jpg

从代码来看
似乎是这个 PH 1 MD PWB 板子上的保险管或者电容有短路
导致了某个驱动转动有问题

EXAMPLE: (coordinates D-1 on BSD 1.40)

CR41 not lit

Fuse F8 is indicated on BSD 1.48

BSD 1.40 shows V-Tra Motor 1 Fuse 8 status can be troubleshot using BSD 10.1

根据以上提示目测 CR41的电容灯是否正常
然后看 F8这个地方

PH 1 MD PWB 是下图所示的位置的10号
10号.jpg

不过建议楼主暂时忍了吧还是工程师来了再说
或者重启就好了或许真的是板子有问题